Quickdata Quikstop-15 Operations Instructions download pdf (Page 24)

Subject to change without notice

Owner Manual

Operating Instructions

2.1A-30004-A02

Page 24 of 36

LINCOLN GmbH & Co. KG  Postfach 1263  D-69183 Walldorf  Tel +49 (6227) 33-0  Fax +49 (6227) 33-259

Technical Data

Pump

Admissible operating temperature............... -40° C to 70° C*

Number of outlets ......................................................... 1,2 or 3

Reservoir capacity ..................................................... 2 l, 4 l, 8 l

Filling................................ via hydr. lubrication fitting from top

Lubricant ................................................ Greases up to NLGI 2

Protection..................................... IP6K 9K acc. DIN 40050 T9

Reverse polarity protection:

The operating voltage inlets are protected against reverse

polarity.

*NOTE: The pump is suitable for the above mentioned

temperature range. Lubricants, however, can normally be

dispensed up to -25°C only. For lower temperatures, low-

temperature greases have to be applied.

Pump element with fix output

Piston diameter, K5 ......................................................... 5 mm

Output ....................................................... approx. 2 cm³/min

Piston diameter, (standard) K6 ...................................... 6 mm

output ...................................................... approx. 2,8cm³/min

Piston diameter, K7, ........................................................ 7 mm

output ......................................................... approx. 4cm³/min

Max. admissible operating pressure. ........................ 350 bar

Connecting thread ............................................................ G 1/4

suitable for tube diameter ........................................... 6 mm

suitable for tube diameter ........................................... 8 mm

Pump element with adjustable output

KR ....................................................... 0.04 up to 0.18 cm³/Hub

.................................................................... 0.7 bis 3 cm³/min

Connecting thread .......................................................... G 1/4

suitable for tube diameter ........................................... 6 mm

suitable for tube diameter ........................................... 8 mm

IMPORTANT: The outputs indicated refer to greases of NLGI

grade 2, measured at 20°C, 100 bar backpressure and 12V/

24V operating voltage. Any differing pressures or

temperatures result in different lubricant outputs. Any system

design must be based on the above values.

Tigthening torques

Install pump .................................................................... 18 Nm

Electric motor on housing .............................................. 12 Nm

Pump element in housing ............................................. 25 Nm

Closure plug in housing ................................................ 12 Nm

Return line connector in housing ......................... 10 - 12 Nm

Electric values DC (direct current)

Operating voltage....................................... 12 V, - 20%/+ 30 %

Max. operating current ....................................................... 2,0 A

Operating voltage....................................... 24 V, - 20%/+ 30 %

Max. operating current ....................................................... 1,0 A

Residual ripple in relation to the

operating voltage.........................± 5% acc. to DIN 41755

Note: The pump motors are suitable for interval operation

only.

 Additionally to the EMV regulation, the DC systems

comply with the following directives and standards:

- Vehicle guideline 95/245/EC

- EN 40839 parts 1, 3 and 4

Time setting

Factory setting

Pause time ........................................................ 6 hours/cycle

Pause time range .......................... 4 minutes up to 60 hours,

.................................................................. , increment 1 minute

Relay for malfunction

malfunction/ low-level control

Switching voltage ..................................... max. 48 VAC/ VDC

Switching current .................................... max. (resistive) 2 A

Switching capacity .................................... max. 100 VA/80 W

Note: All data depends on operating voltage, ambient

temperature and max. operating pressure.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 35 36

Comments to this Manuals

No comments

Quickdata Quikstop-15 Operations Instructions Page 24

Comments to this Manuals